How Much Does Drip Edge Cost?

How do you replace a drip edge?

Replacing Drip Edge Eave Strips:Install the eave strips on the lower roof edges first, with the eave strips under the shingles and felt underlayment.Align one end of the lower eave strip even with the edge of the roof decking.Lift up roof shingles, and nail the eave strip in place with galvanized roofing nails.More items….

Do you need drip edge on gable ends?

What’s a drip edge? A drip edge is a piece of roofing trim. The drip edge supports overhanging shingles at the ends of a roof, providing structure to the overhang and directing water to the gutters and away from the fascia of the roof. … Drip edges can also be installed on the gable ends of a roof.

How is drip edge installed?

Roof drip edge flashing corner detail Install roof drip edge along the eaves, add underlayment, then place drip edge along the gable end. The best way is to install the roof drip edge only along the eaves first, then place ice-and-water barrier (in the snowbelt) or felt paper (underlayment) over the drip edge.

Do all roofs need a drip edge?

Without a drip edge, water may end up beneath the shingles and may cause damage to various parts of the home. Though your home may not have originally had a drip edge installed, drip edges are now required by most building codes across North America to protect homes from damage.

Should drip edge be painted?

Yes you can paint the aluminum drip edge and it hold up very well. Just be sure it is clean and paint it with a good exterior acrylic primer and finish with a exterior acrylic semi-gloss house paint.

How much should shingles overhang drip edge?

Shingles should not extend more than 3/4” (19 mm) past the drip edge. If shingles overhang the edge of the roof by more than 3/4” (19 mm), then they are not supported and may crack and break off. In addition, the wind resistance at the roof edge may be compromised.

How do you add drip edge to an existing roof?

Make sure the outer edge extends over the gutter. If it doesn’t, pull the drip edge out slightly from under the shingles. Secure the drip edge with roofing cement. Apply a continuous bead of cement along the top of the drip edge, then press down on the shingle.

How do you calculate drip edge?

The drip edge metal is only used at the bottom edge of roofs – near the gutters. Measure the length and add 10% to find how much drip edge you will need.

What is a drip edge used for?

Drip edge is a metal flashing that is installed at the edges of the roof to help control the flow of water away from the fascia and to protect the underlying roofing components. Drip edge overhangs the sides of the roof and has a small metal flange that is bent away from the fascia.

Why is water dripping between gutter and fascia?

Water Gets Behind the Gutter If water is dripping behind your gutter, it’s probably because it was installed without any flashing over the back of the gutter. The gutter apron will prevent the dripping. A gutter apron is a bent piece of flashing that tucks up under the shingles and over the gutter.

Should drip edge be tight to fascia?

Nail thefurring strip to the fascia board near the fascia top – tight under any extending of roof decking (usually absent); the Drip edge will be installed 1/8″ proud of (away or out from) the furring strip in best practice or may be installed tight against the furring strip (reduces the life of the furring strip by …

Does gutter go under drip edge?

Your gutter needs to be a few inches under the edge of your roof. … Drip edge gets installed under the first course of shingles and promotes water to run freely from roof edge down into gutter. Without it, water may run down behind your gutter, down fascia board and siding, leading to potential damage.

How do I estimate roofing costs?

What Should Be Included on Your Roof Estimate?Payment Information. … Approximated Timeline. … Costs. … Roof Estimate Materials. … Full Description of Work. … Guarantees and Expectations of Work. … Warranty. … Insurance and Licensing Information.More items…•

Can you install drip edge over existing drip edge?

If the old drip edge is installed behind the gutter or the gutter is screwed through the drip edge and it cannot be removed without removing the gutter it is better to leave it there and install the new drip edge on Top. We do not remove and reinstall aluminum gutters.

What is the difference between drip edge and rake edge?

Drip edge and rake edge are the first parts of the roof system to be installed. … They form a long, narrow piece of metal, which is installed along the perimeter your Roof Deck. Drip edge goes along your eaves trough areas and rake edge goes along your gable ends.

What color drip edge should I use?

If your home’s trim and fascia are white, it is recommended you select a white drip edge for seamless blending of elements throughout. If your home has more pops of brown, similar to the home displayed in the photo to the right, you may want to choose a brown drip edge.

What size drip edge should I use?

I usually select drip edges with at least a 4-inch roof leg along the eaves edge and a 2-inch leg along rakes. The code calls for the fascia/rake leg to extend 1/4 inch below the roof sheathing and the Fortified Home guides call for 1/2 inch. But I like to use drip edge with at least a 1-inch fascia/rake leg.